English
ODROID-HC4-P KIT
₩123,600
Consists of ODROID-HC4 board, a case made of a rigid PCB that can mount two 3.5-inch HDDs horizontally, cooling fan, cables and bolts. It’s your own network storage device that you can enjoy creating yourself, and the HC4’s Petitboot function and various latest OS support can be used without any changes. Please note that this product cannot mount any 2.5-inch storage device.
Note! This KIT does NOT include OLED+RTC for HC4-P. (Sold individually)
Board Detail
| A | CPU (Amlogic S905X3) | H | 2x System LED indicators |
|---|---|---|---|
| B | DDR4 memory (4GiB) | I | 1x UART for system console |
| C | 2x SATA ports | J | 1x IR receiver |
| D | 1x RJ45 Ethernet port (10/100/1000) | K | 5x GPIO pins (for optional OLED display) |
| E | 1x HDMI 2.0 | L | 1x Micro SD slot |
| F | 1x USB 2.0 host port | M | 1x Cooling fan |
| G | 1x DC power jack (Outer diameter : 5.5mm, inner diameter 2.1mm) | N | 1x Boot switch |
Block diagram
SATA interface performance
We connected a SATA SSD to the HC4 platform and measured the storage IO throughput. We could observe 390~420MB/s transfer speed which is not saturated at the maximum level ~500MB/s which is quite good for many applications.
odroid@hc4:/media/ssd2$ iozone -e -I -a -s 100M -r 4k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.489 $ Compiled for 64 bit mode. Build: linux-arm random random kB reclen write rewrite read reread read write 102400 4 44097 62373 75362 75511 39859 60806 102400 16384 428515 426902 390226 392564 391412 427137 |
SMB/CIFS network file transfer performance over the Gbit Ethernet connection
As shown below Windows OS client shows a sustainable 100+ MB/s transfer speed when we download/upload large files.
Downloading
Uploading
Helios LAN Test Result
Samsung 860 EVO 250GB SSD
Seagate Barracuda 2TB HDD (ST2000DM006)
Power Consumption
Note 1: ST2000DM006 spin-down power consumption is 0.75W per HDD. Therefore, the HC4 idle mode power consumption is about 4W.
Note 2: Power consumption in Active state is tested while copying huge files through SAMBA service.
Note 3: Wake-up sources for the Suspend mode: Wake-on-LAN, IR remote receiver and RTC Alarm.
Software Support
Petitboot can find the OS on the SD card, the HDD or the SSD. So even if you do not have an SD card but you have a plugged-in HDD or SSD that has an OS installed, Petitboot will boot the HC4 using the OS from the HDD or SSD. Debian/Ubuntu OS can run with the Hardkernel’s preinstalled OS image or Debian/Ubuntu Netboot Installer which you can obtain from the ODROID forum.
Supported Linux kernel versions are:
- 4.9.230 or newer (Hardkernel stock OS version)
- Mainline kernel 5.15 or newer (Unofficial version from ODROID forum)
Specifications
| FORM FACTOR | Board Dimensions: 84mm x 90.5mm x 25.0mm Transformation KIT Dimensions : 225mm x 106mm x 127mm Weight: 615g including board and transformation KIT without HDD |
|---|---|
| PROCESSOR | Amlogic S905X3 Processor L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processorsQuad-Core Cortex-A55 (1.800GHz) ARMv8-A architecture with Neon and Crypto extensions Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz) |
| MEMORY | DDR4 4GiB with 32-bit bus width Data rate: 2640 MT/s (PC4-21333 grade) 1.2Volt low power design |
| STORAGE | 1x Micro SD slot (DS/HS mode up to UHS-I SDR104) |
| NETWORKING | 1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps) – Realtek RTL8211F (Ethernet transceiver) – LED indicators * Green LED: Flashing by data traffics at 100Mbps connection * Amber LED: Flashing by data traffics at 1000Mbps connection |
| VIDEO | 1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID) |
| AUDIO | 1 x HDMI digital output |
| COOLER | Passive heatsink ( 40x32x10 mm ) on the CPU of PCB board Bearing : Hydraulic Bearing FAN – Rated Voltage : 5V – Rated Current : 0.2A – Max Speed RPM : 2000RPM – Air Flow CFM : 33 – Air Pressure (In H2O) : 0.08 – Noise Level(dBA) : 26.5 – Dimension : 92X92X25MM – Wire & Connector : 150mm, 4pin 1.25mm pitch |
| EXTERNAL I/O | 1 x USB 2.0 host port 1 x Debug serial console (UART) 2 x SATA Connectors |
| OTHER FEATURES | IR receiver for remote controller System LED Indicators: – Red (POWER) – Solid light when DC power is connected – Blue (ALIVE) – Flashing like heartbeat while Kernel is running. |
| POWER | 1 x DC jack : outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm DC input : 14.5V ~ 15.5V – DC 15V/4A power adaptor is recommended. Sold separately. Power consumption with two ST2000DM006 HDDs : – IDLE(with HDD in spin-down) : ≃ 5.88W – Active(using SAMBA): ≃ 15.59W – Suspend: ≃ 0.29W |
WIKI
https://wiki.odroid.com/odroid-hc4/odroid-hc4
GTIN : 8809543642539
- The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI Trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
- HDMI, HDMI High-Definition Multimedia Interface(고화질 멀티미디어 인터페이스), HDMI 트레이드 드레스 및 HDMI 로고라는 용어는 HDMI Licensing Administrator, Inc.의 상표 또는 등록 상표입니다.
Compatible Products
연관 상품
